Security Systems For Home

It seems that most accidents have in common the fact that they could have been avoided with a little more care and attention. Although most of them can be prevented, people generally think that accidents only happen to other people. However, statistics on the damage caused by accidents, are truly amazing. Although there has been remarkable progress in reducing deaths from various diseases, the death rate from accidents has decreased very little.In fact, they rank fourth as the cause of death in the United States. The deaths of children between the ages of 1 and 14 are caused more by accident than by the following diseases taken together: tuberculosis, diphtheria, polio, syphilis, rheumatic fever and appendicitis, all more murders cause fewer deaths per year accidents occurring in the home. Every year in the United States about 29,000 people due to home accidents. This figure should be enough for parents to think very well in the chances of accidents and make the word "neglect" cease to be part of your vocabulary.

 Different types of accident

The different kinds of accidents that commonly occur in the home will be listed below with some of their possible causes. This may serve as a checklist of precautions to take to ensure security at home.

 Fallen

Accidents caused by falls are the most common in the home. In fact, almost half of all deaths from home accidents are caused by falls. Preventing these depends essentially on proper maintenance of floor surfaces (both outside and inside the home), care to eliminate any dangerous obstacle. To help eliminate the common causes of falls, the following precautions are recommended: Take care that the sidewalks are in good condition, remove the branches or other objects that obstruct the passage and check the porches and stairs of the house are secure without obstacles. Ensure that wire cloth racks, shutters or other protection placed in the windows are securely fastened. Periodically review stairways and steps to see if any repairs are needed. Securely tightened using ladders, rather than boxes or chairs.

No climbing stairs with arms full of objects, or climb the stairs two by two or more. The waxed floors must guard properly. You have to rub the wax well to afford a sticky surface. With repeated waxed, entire floor becomes increasingly slippery, which is why the wax must be removed after being applied five consecutive times. Rugs and carpets should be placed in appropriate locations and anchored securely to the floor. Care should not have holes or bent edges.  

The base rubber mats should be reviewed regularly as it wears washed or impregnated with wax floors. Floors and stairs should not have misplaced furniture. The chairs and tables, for example, should not obscure the view of a staircase or obstruct free access to a room. This also applies to other objects that may have been left stranded, as children's toys. They will learn safety habits accustomed to keep their toys after having played with them. Electrical cables are also risks to be taken into account. They should be placed behind furniture and away from places where you walk. Finally, it is necessary to use appropriate and comfortable shoes. Shoes with slick soles, slippers or walk in socks or barefoot are not recommended practices on certain types of surfaces.

 Fire, burns and electric shocks

Since the heat and fire are essential in everyday life to heat the house, cooking and even smoking, special attention should be given daily to the risks inherent in the use of fire. Among the most dangerous and important elements to be taken into account include: equipment and faulty electrical wiring, smoking habits and the misuse of matches, the smooth operation of heating equipment, proper maintenance of the stoves oil, spontaneous ignition of garbage, he inappropriate use of flammable liquids, hot ashes and placing fuel in places near the heaters.

How to hide the bathroom door

In a home environment, relatively small , recover space is of vital importance . For this reason, in the process of furnishing is necessary to study a number of solutions indicated precisely this purpose . Or in the case where the space is not a problem , however, solutions to make it look like a still larger. Many solutions may be available to us, in this guide we will see how to hide the bathroom door recovering space, but at the same time furnishing.

Hide a door, nowadays it is not a problem , just give space to the imagination, and the solution comes totally unexpected. Let's start to see how to hide it in case we wanted to conceal the continuity of the house giving the illusion that the apartment is still in the room next to the bathroom .To create this effect we would need to achieve a kind of library in which should be applied a hidden mechanism able to open like a door. The library in question will inevitably be chosen based on the furnishing of the room in which it is placed. If our furniture is classic library will also be classic, but if the room is modern, consequently, the library will follow this line.For the inside , the one from the bathroom, we could choose to leave it smooth, or apply some ornament or decoration.

If we are lovers of the simple things , then in this case we may opt to hide our door behind a simple curtain. Of course, the fabric must be matching with the decor and also draw the curtains a little present at the windows of the room so as not to clash, and then deviate too much from furniture. As a type of fabric instead must be large enough to fall in an appropriate manner and cover with sobriety port that is hidden behind it. The fabrics most suitable for this purpose may be quite heavy velvet or linen.

Instead we see a solution to mask both the bathroom door which to recover space. This solution is particularly suitable when our apartment was not big and spacious. To realize this idea will be enough to get a carpenter to build a false door, in wood, very rough, which will be mounted on a sliding mechanism to view. To keep the rustic, simply spend more coats of varnish on the wood, so as to give luster to the door , but also enhance the beauty of the wood with which it was made.

Shower Column Reviews

When we install a shower especially in the garden, you have to build it in the column.This assembly includes the construction of a slender paralleled on which is fixed a shower head and taps to mix the water. They must be connected to the structure of the pipes that draw water from the main source donor . Let us see in detail how to install a shower column .

In the market you can find shower columns have been processed or finished with tiles, or just metal to be coated with any material. If you opt for the solution of DIY, we can also make the column directly in masonry and then cover it to our taste and maybe relevant to the whole furniture of the garden.

For the construction of the shower column , which must be at least 190 cm high, we provide the concrete blocks that superimposing them on one another in the stack, glue them with a mixture of mortar and concrete. Once you reach the desired height we take care of practice on the upper part of the column shower hole for attaching the head, and in the lower holes for the two knobs respectively hot and cold water. At this point, with the canes copper on the back of the column, we link together the various holes and make them converge in a pvc pipe about 4 inches in diameter, which leads directly to the source. These can be hidden in the ground or distributed along the perimeter of a wall in the lower part . Once the hydraulic part we just have to go to the finish. First, we take care to install the knobs at the bottom to about 1 meter from the ground, and the head that is attached directly to the column.

If you need to install a shower column in a bathroom inside the house, you can choose between different models and design and having already funnels for various water pipes, the shower column should be applied directly on the tiles with the file to four sides. At this point, you can complete the installation with the assembly of knobs and water supply, and the head of the rod that supports it.

How to refurbish furniture

When you have furniture in the house of a certain value, we should treat them in a certain way to make sure that these pieces of furniture can always be in excellent condition, and maintain as long as possible their beauty, their beauty and their value. As we know how to refurbish furniture, in fact, valuable furniture pieces, usually in old style (if not old) have a great value, and the same rule also applies to those of wood of a certain level. In this guide we will cover how to care for the high-quality furniture at its best.

The first rule to follow which will allow us to keep the furniture of a certain value and shining at the top of their beauty, is to place them in the right place. If for example the fine furniture and wood, you should try to place it in a corner or in a room not particularly moist and subject to particular changes in temperature. The humidity, as we know, is one of the worst enemies of wood, and the same rule applies to the furniture of the same material. Even if they are treated with special products, in the long run may skew ruinous that threaten its beauty.

Also with regard to the location in the house, avoid that they are positioned in a place where the sun's rays arrive direct on mobile. In the long run the sun wears out the natural color of the cabinet off and making it opaque. Alternatively, during exposure to the sun should keep open the curtains so as to cushion the effect of the sun. To keep the cabinet always perfect, cleanliness is important. Every day you have to clean the furniture from dust with a feather duster. Periodically, however, you must provide the following.

Take a wool cloth is very soft and impregnate with straw oil. Pass the oil over the entire surface so as to revive the natural color and shine of the mobile. Need to do this operation over the entire surface of the cabinet. This must be done at least a couple of times a year. Also, do not use detergents, detergents, sprays that are not suitable for the type of material it is made mobile. You can use the wax and oil but avoid any type of cleaning agent that can dull the color of the furniture forever. Never use scouring pads that are not absolutely fluffy and soft otherwise you risk scratching the surface .

   

How to decorate a child's bed

As children grow, they need a decor that is appropriate for their age and then to their needs.Well, if your family budget does not allow you to buy a new bed , you can, with a bit of imagination and creativity , adjust the bed for their children according to their age without having to spend a fortune. Here, then, are some tips on how to decorate a child's bed .

If the mattress is not in good condition or if the file size is more age-appropriate, purchase a new one and above all quality. Regarding the table, take a simple stool of unused timber, strip him of old paint, cut the four feet and paint it with a color that reflects the tone of the room furnishings.You can also paste stickers or possibly make some stencils. For the back of the bed , instead, may be used for wood siding. To make these coatings, we must first of all take the exact measurements of the width of the bed, then attach two studs at the ends of the network to be able to screw in the back. It is also possible to also use the old staves of wood, uniting them together and valedictorian.

If you then want to create a canopy craft, you can use fabrics for curtains or simply the sheets. Make a rectangle with the fabric and sew it, install at least six eyelets to tie the fabric to the baccarat . You can also add a phrase such as "sweet dreams" fabric felt.

If you want, you can serve the technique of decoupage in the personalization of the child's bed . From the moment you take several printed sheets , you should use pre-printed paper napkins instead of using glue to stick the designs on each sheet.  The paper towel is usually composed of three layers (two white, one printed), delete the white ones and just keep the printed .

Choose a good reason. The decoupage is practiced on any material: wood, metal, plastic, PVC, etc.. This is a good technique to give life to a bed. Use a colored thread to embroider letters or numbers, or, to make it more fun, you can use the custom stickers , remembering always to combine the right colors.

How to lay the concrete bricks

If in a house we must make a brick building, whether it be of a partition wall , a wall or a fence of flowerbeds, we can do so in a simple, economical and the process is the same for all types of buildings. Let us see in this guide as laying the concrete bricks .

First, we are concerned to take the necessary measures in order to purchase concrete bricks in the right quantity. With them we also need specific material for the construction industry including cement and mortar, and of course some basic tools such as a trowel, a putty knife, a water level drop and a container for the mixture of adhesives and grout cement.

Now, to begin the work of laying of concrete bricks must be paid from the bag of cement mortar and the dose needed to create the dough for the base of the bricks, while avoiding the excess since the processing time of the laying of the latter could be long, and then the mixture may dry too. At this point, leans against a first row of bricks of the required width, liveliness perfectly the exact position, using the wooden pegs and obviously the level. After finding that everything is perfectly level, rise one by one the bricks and concrete are fixed to the ground with the mixture of mortar and concrete. With the same procedure, the salt thus upward, using from time to time mortar and cement, and the level to check the exact position.

It therefore realizes the base with the laying of the first row of bricks in concrete, which must be durable and also very compact, whereby the bricks are always put in a staggered manner so as to meet the end with a wall up and with the weight of every single brick equally distributed between the parties Everything is important from the static point of view and also aesthetic, just think that the ancient Romans, they had realized the importance during their colossal buildings . Completed then the laying of concrete bricks, we just have to sand the surface, free it from leaking excess glue and possibly Staining  with the desired color, or smoothing it and leave it with the natural color, using only the flatting of transparent or simply ' straw oil. 

How to plaster a brick wall

Many people have outside the house one or more walls made ​​of bricks that are sometimes unpleasant or maybe out of date.Even an interior wall , such as a fireplace or an interlude between two environments sometimes you want to change and intonation so that you can decorate with wallpaper, wooden beads or simply paint it. This may seem hard to realize however, is not at all but requires only some basic processing methods . Here is how plastering a brick wall .

First you have to prepare the surface of the bricks so they should be cleaned making them free of dust and dirt. The bricks damaged can be repaired with stucco and filled with concrete made ​​of cement and mortar . When the brick wall is compact after the restoration, then proceed wetting the wall with a sponge soaked in water. It 'important fact that the surface is sufficiently moist so that applying the plaster there is a good binding between it and the bricks.

Just with the grout starts the hedge of the brick wall. The stucco for walls, is generally available in powder or ready and must be applied in the spaces so as to avoid the grooves between a brick and another, which could create problems for the purposes of filling and excessive waste of mortar and concrete. After the filling of the spaces between the bricks, you start with a first coat of cement and sand (mostly) to create the insulating part that, once dried encourages the application of the plaster finish. After waiting and then drying the mixed sand and cement, we proceed with a first coat of plaster put roughly with the aid of a trowel and during the step of drying , it begins to straighten it with a pole in wood and with a damp cloth . In this way the bricks are covered with a layer of about one centimeter between concrete and plaster.

The brick wall, then becomes a normal wall masonry, is accomplished with the phases of processes typical in fact Proceed with sanding and finishing after that, once dried, the wall must be sanded and coated wall painting, with saved a cloth or paper. The plaster at this point is perfectly smooth and the bricks behind it will be only a distant memory compared to a completely transformed. 

How to build a low table

An element really handy when you decorate a living room is definitely the coffee table comfortable when placed in front of sofas and armchairs .In the market you can find an endless array of models in every possible style, modern, classic,minimalist . Despite this immense variety , however, you may not be able to find what we seek, a model that meets our needs. At this point the only thing to do is definitely build with their own hands. In this guide we will see how to build a low table.

Before starting with page construction itself, will have to make some estimates of the type: a decor which combine such functions must be carried out, if in addition to a normal table we also want to be an element of decorum and finally how much is the figure that we are willing to spend for the creation of this item. Based on all these answers we might begin to outline a precise model.

If you do not have in mind anything definitive, so Terrance still in the dark, then you could take a ride on the internet and find out if one of the many ideas that are present, you can find something that suits you in terms of aesthetics.Just to help the undecided, we suggest some ideas to make with simple materials recovery then in addition to exclusive models also really very cheap. Let's start with an idea really nice, easy to implement. Obtain 5 wooden beams 14 x 14, the length 70 cm, 6 x 6 quadriplegia also the length of 70 centimeters. To retrieve this material you might go in a carpentry workshop, many times you can find scraps at affordable prices. Once home to prepare the equipment for the construction, sander, in the absence sandpaper in various grits, drill, wood screws , silicone transparent , clear coat , dark paint water-based.

With the sander or sandpaper, sand the boards so as to remove any splinters and make the surface as smooth as possible to do a good job, use the sandpaper of various sizes starting with the coarse, then medium and finally end. When the wood is well polished past a coat of varnish and let dry Once dry the paint repeat the process until the wood is not reach the tone you prefer Meanwhile prepared the logs that will serve as bases Always with the sandpaper polished wood, paint them with water-based paint in a dark color so that once mounted stand out from the color of the table, let it dry back to work on large beams, take the first, on the side past several rows of silicone, combined with the second and continue in this way until you get to the fifth Let dry for a few hours is now time to mount the quadrilateral  which will serve as bases, secure with wood screws of the measure 10 cm in order to get a grip, keep a distance of 3 cm apart Repeat with the other quadrille. The coffee table is ready to be flaunted in your living room .  

Maintenance Guide wrought iron

When you think of iron as part of furniture come to mind immediately all those beautiful forms, some a little baroque which are used in gates, beds, railings, balconies. Although it is a "cold" material, through its processing is able to transmit a note of heat enveloping. Just think of those beautiful balconies , fully realized in this material with their rounded shapes can completely change the austere facade of a building, or to those majestic gates , also made ​​with the same material, real works' art, which give to those who watch them feeling of grandeur. So we try to suggest, as far as possible, a small guide to the maintenance of wrought iron.

Although at first glance it might seem a durable, really need for regular maintenance in order to always remain at the height of its splendor, and then last. Let us see how to take care of the right way. For its maintenance, we would need sandpaper average at the end of brush, iron , rust inhibitor, and paint coverage. We begin our work. With the sandpaper media begin to push aside the iron taking care to pass on the entire surface to be treated, the past must be confident and decisive. Once we have sanded everywhere by removing the parts that may have rusted, go over again but this time we will make use of fine-grained sandpaper. We must not leave behind even one small piece, the surface must be completely sanded.

In the case we were in front of some points which prove a little difficult parts because of the shape or position, in this case, we could replace a run the sandpaper with a sharp also in iron. The parts to be treated are more corners, welding processes, curls decorations. Once our object has been completely stripped, let's controllable he there are no holes, welding etc. that are failing. If you were in the presence of holes, then we should take immediate action to closure using special material as a filler for iron. To use it you will need to follow the instructions that are behind the pack. Even when all the holes will be placed, clean up the object in question with a purpose, a rag, or if the surface is very large with the use of compressed air. This maneuver will ensure that all the dust of processing has been eliminated.

Now proceed with the application of a coat of rust, let dry, and for good measure another impassioned When the last is dry we can proceed to the actual painting. We pay careful attention what kind of paint we use for objects made ​​of iron will in fact be obliged to use one specific At this point, our object can be said to be completely refurbished, averted the danger of rust and paint restored Maintenance is now complete but attention as soon as you realize that the rust comes back in some places, run for cover, without wasting precious time. 

How to make a wooden table and stone

With the DIY is possible to realize a large number of objects, even the most disparate, those words that our imagination suggests.Sometimes the use of this art, it can mean really save much money and earning a lot of satisfaction when the work is performed in a workmanlike manner, and the results reflect our expectations to the full. In other cases, the do it yourself can be a real art form, which allows us to create objects in our complete liking . In this guide, we'll see a few ways to create a table in wood and stone , how to do, what materials to use in short, everything that can be useful in this building.

Suppose that we want to decorate a corner of our garden to make it more intimate and personal. The idea is to create a table, but it has very special characteristics. First of all, the choice of materials or wood and stone , two important elements of our system, two materials that are definitely the symbol with regard to the construction and furnishing.  Let's start with an idea to suggest very colorful and affordable for everyone in terms of achievement. To speed up the construction time, we could use an old garden table we thought of throwing. If you encounter any problems in the structure, we will try to remedy repairing it, but if everything conforms we can start our construction.

Let us go into a pottery shop or at a department store specializing in building materials. Ask us to view the sampling of natural stones available to them. Once we have them available for examination will think about which one to choose to match with our table. The idea basically consists in covering the table top which originally made ​​of wood, with natural stones we have chosen. To do this we need: natural stones to our liking (marble, granite, rough stone) glue , and a product for leaks.

Once home we place our stones on the table trying to arrange them so that they fit within the table without overhang and in any case are also pleasing to see once you have found the right accommodation prepare the glue adequate, spasmodically under every stone moving them one by one. Let dry When you are sure that the stones we made ​​adherence to the table, prepare the liquid compound that will serve to fill the gaps, trying to abound with the material so as not to gaps At this point, even when this liquid is dried, can pass over the floor a product polishing and protective The same idea can be realized with the use of ceramic tiles, both whole and broken mosaic. 

How to make a folding table

Do you have a tiny house , but always ready to welcome friends and relatives? You therefore need a large table for only a few occasions, but would be too cumbersome for everyday? Well, then you're in the right place!Keep following this article and discover some ways on how to make a folding table .

In the first case, we present a folding table, in which one of the sides, is leaning against the wall. Once the measures taken on the dimensions of the wall , cut two sides in wood, one will serve as a tabletop (its measures correspond, therefore, to those chosen for the mobile), the 'other, however, will be juxtaposed with a para wall to ward off the blows when the table is open. Bring hour meter and a pencil and take the measurements from the ground, on the wall and mark the two points of reference where you want the 'height of the table and draw a connecting line.

Now take the board more closely and apply a layer of glue on the back, then lean it up against the wall along the line drawn, for a tighter seal recommend you nail it. Below the bumper , are now applied two strips of wood, which reach down to the floor, connecting two of these are squares hinged on the underside of the bumper, must now apply two hinges that serve to connect it to what will be the table. In this way, when the plan is turned down, he is on the brackets, which will serve as a support when the table is open.

A table structured as will be useful in the kitchen, especially if there 'is a lot of room to move, you can use a table to disappear as floor support to cook, then once finished it closes to allow free passage.A second example we expected in practice two pieces of furniture in one: in fact it goes build a shelf or a belief, which is attached to the wall L 'unit door, once opened, it becomes the plan' support. In this case, the legs of the table are given by a family-pi Greek, whose horizontal part is attached by hinges to ' end of the shelf away from the wall, of course, regardless of the solution you choose, you can indulge with the colors to give to your table, as you can also choose to coat the wooden shelf with king materials such as Formica or tiles, but in any case it 's important to remember always good to sand the boards before you start decorating.  

How to decorate a shoe box

If you're creative and are willing to engage yourself with the craft, this is the tutorial for you. In detail it will show you how to decorate, in various ways , a shoe box . With these techniques you will be able to have the boxes all different from each other and above all give a touch of color to your shelves in most shoes. For more tips , you just need to read the content that follows.

The first concerns the decoration sheets of newspaper. In this regard, cut from newspapers and magazines, photos that most affect your attention. Having thus chosen landscapes or photos of your favorite characters, have fun to glue them on the shoe box . There will be enough glue, scissors and newspaper to have a truly original box .

The second idea , more innovative, instead consists in the use of stencils. It is of special molds that must be combined with colors or tempera. As for the cardboard box, apply the template you prefer (hearts, stars or flowers), and begin to fill it with colors instead of fluorescent lamps. A tip for the fantasies even more original is the sponged effect. To get it, just give the color temperature of a kitchen sponge and wipe "accidentally" on the box. The result will be amazing and guaranteed.

For those who love a confident style, even in the DIY , we recommend the use of glitter To apply you will not have to do is spend a layer of glue stick on the box and then sprinkle with the glitter or colored sequins. Again originality and brilliance will be insured.