When you think of iron as part of furniture come to mind immediately all those beautiful forms, some a little baroque which are used in gates, beds, railings, balconies. Although it is a "cold" material, through its processing is able to transmit a note of heat enveloping. Just think of those beautiful balconies , fully realized in this material with their rounded shapes can completely change the austere facade of a building, or to those majestic gates , also made with the same material, real works' art, which give to those who watch them feeling of grandeur. So we try to suggest, as far as possible, a small guide to the maintenance of wrought iron.
Although at first glance it might seem a durable, really need for regular maintenance in order to always remain at the height of its splendor, and then last. Let us see how to take care of the right way. For its maintenance, we would need sandpaper average at the end of brush, iron , rust inhibitor, and paint coverage. We begin our work. With the sandpaper media begin to push aside the iron taking care to pass on the entire surface to be treated, the past must be confident and decisive. Once we have sanded everywhere by removing the parts that may have rusted, go over again but this time we will make use of fine-grained sandpaper. We must not leave behind even one small piece, the surface must be completely sanded.
In the case we were in front of some points which prove a little difficult parts because of the shape or position, in this case, we could replace a run the sandpaper with a sharp also in iron. The parts to be treated are more corners, welding processes, curls decorations. Once our object has been completely stripped, let's controllable he there are no holes, welding etc. that are failing. If you were in the presence of holes, then we should take immediate action to closure using special material as a filler for iron. To use it you will need to follow the instructions that are behind the pack. Even when all the holes will be placed, clean up the object in question with a purpose, a rag, or if the surface is very large with the use of compressed air. This maneuver will ensure that all the dust of processing has been eliminated.
Now proceed with the application of a coat of rust, let dry, and for good measure another impassioned When the last is dry we can proceed to the actual painting. We pay careful attention what kind of paint we use for objects made of iron will in fact be obliged to use one specific At this point, our object can be said to be completely refurbished, averted the danger of rust and paint restored Maintenance is now complete but attention as soon as you realize that the rust comes back in some places, run for cover, without wasting precious time.
Although at first glance it might seem a durable, really need for regular maintenance in order to always remain at the height of its splendor, and then last. Let us see how to take care of the right way. For its maintenance, we would need sandpaper average at the end of brush, iron , rust inhibitor, and paint coverage. We begin our work. With the sandpaper media begin to push aside the iron taking care to pass on the entire surface to be treated, the past must be confident and decisive. Once we have sanded everywhere by removing the parts that may have rusted, go over again but this time we will make use of fine-grained sandpaper. We must not leave behind even one small piece, the surface must be completely sanded.
In the case we were in front of some points which prove a little difficult parts because of the shape or position, in this case, we could replace a run the sandpaper with a sharp also in iron. The parts to be treated are more corners, welding processes, curls decorations. Once our object has been completely stripped, let's controllable he there are no holes, welding etc. that are failing. If you were in the presence of holes, then we should take immediate action to closure using special material as a filler for iron. To use it you will need to follow the instructions that are behind the pack. Even when all the holes will be placed, clean up the object in question with a purpose, a rag, or if the surface is very large with the use of compressed air. This maneuver will ensure that all the dust of processing has been eliminated.
Now proceed with the application of a coat of rust, let dry, and for good measure another impassioned When the last is dry we can proceed to the actual painting. We pay careful attention what kind of paint we use for objects made of iron will in fact be obliged to use one specific At this point, our object can be said to be completely refurbished, averted the danger of rust and paint restored Maintenance is now complete but attention as soon as you realize that the rust comes back in some places, run for cover, without wasting precious time.
No comments:
Post a Comment